Assessment of accredited calibration laboratories

PRM tasks solved by the Czech Institute for Accreditation

Outputs from the tasks of the Metrology Development Programme Czech Institute for Accreditation:

 

• Task No. VII/5/09 Preparation of documents for continuous unification of assessment of accredited pressure calibration laboratories - final report (PDF 216 kB)

 

• Task No. VII/5/10 Preparation of documents for continuous unification of procedures of accredited calibration laboratories in the field of temperature - final report (PDF 378 kB)

 

• Task No. VII/5/11 Preparation of documents for continuous unification of procedures of accredited calibration laboratories in the field of electrical quantities - final report (PDF 564 kB)

 

• Task No. VII/4/12 Preparation of documents for continuous unification of procedures of accredited calibration laboratories in the field of geometric quantities - final report (PDF 1 393 kB), Annex 1 (PDF 138 kB), Annex 2 (PDF 518 kB), Annex 3 (PDF 111 kB), Annex 4 (PDF 393 kB), Annex 5 (PDF 461 kB), Annex 6 (PDF 219 kB), Annex 7 (PDF 164 kB), Annex 8 (PDF 274 kB)

 

• Task No. VII/5/12 Preparation of documents for continuous unification of procedures of accredited calibration laboratories in the field of electrical quantities - final report (PDF 706 kB)

 

• Task No. VII/4/13 Optimisation of the use of MPZ in accredited calibration laboratories - final report (PDF 662 kB), MPA change sheet (PDF 75 kB)

 

• Task No. VII/5/13 Introduction of the service "Accreditation of reference material producers" into the accreditation system of the Czech Republic - final report(PDF 132 kB), Annex 2 - Methodology (PDF 375 kB), Instruction one (PDF 36 kB), Instruction 2 (PDF 24 kB)

 

• Task No. VII/5/14 Preparation and use of "in-house" reference materials for quality control in laboratories - final report (PDF 401 kB), note - the actual translation of ISO Guide 80 will be published as TNI (2015)

 

• Task No. VII/4/14 Optimisation of the use of interlaboratory comparisons and proficiency testing in accredited calibration laboratories (ACLs) - final report (PDF 580 kB)

 

• Task VII/5/15 Good practice in the use of reference materials and related terms and definitions - final report (PDF 163 kB), note: the actual translations of ISO Guide 33 and 30 will be published as TNI (2016)

 

• Task No. VII/5/16 Reference materials: guide for the characterisation and assessment of homogeneity and stability of materials, translation ISO Guide 35 (PDF 2 926 kB)

 

• Task No. VII/5/17 Basis for continuous unification of CMC calculation in accredited laboratories in the field of temperature - final report (PDF 2 367 kB), Annex (PDF 37 kB)

 

• Task VII/4/18 Basis for continuous unification of CMC calculation in accredited laboratories in the field of volume - final report(PDF 588 kB)

 

• Task VII/5/18 Basis for continuous unification of CMC calculation in accredited laboratories in the field of pressure - final report(PDF 974 kB)

 

• Task VII/5/19 Basis for continuous unification of CMC calculation in accredited laboratories in the field of length - final report (PDF 1,57 MB)

 

• task VII/5/20 Principles of calibration in the field of basic electrical quantities - final report (PDF 1MB) with attachment (PDF 291 kB)

 

• task VII/5/21 Principles of calibration in the field of pressure - final report (PDF 1,488 MB)

 

• Task VII/5/22 Principles of calibration in length and angle - final report (PDF 521 kB) with attachment (PDF 294 kB)

 

• VII/5/23 Unification of uncertainty calculation and calibration principles at POA accredited calibration laboratories in the field of mass - final report (PDF 787 kB)